Hamilton Company | Hamilton Syringes | Technical Information

Syringe Dimensions

7000 Series Syringes

		Outer Diameter Nominal		Inner Diameter Theoretical Bore
Model	Volume (µL)	mm	Inches	mm	Inches

7000.5 (32 gauge)	0.5	7.820	0.308	0.1041	0.0041

7000.5 (25 gauge)	0.5	7.820	0.308	0.1041	0.0041

7001 (25 gauge)	1.0	7.820	0.308	0.1448	0.0057

7101 (22 gauge)	1.0	7.820	0.308	0.1448	0.0057

7002 (25 gauge)	2.0	7.820	0.308	0.2057	0.0081

7102 (23 gauge)	2.0	7.820	0.308	0.2057	0.0081

7105 (24 gauge)	5.0	7.820	0.308	0.3251	0.0128

Note: The plunger of a 7000 series syringe uses a tungsten wire that travels through the syringe to the tip of the needle. The seal is created by a PTFE ferrule within the knurled hub termination. The I.D. of the needle is honed to fit the tungsten wire. The displacement calculation is based on the O.D. of the plunger wire which is displayed as Theoretical Bore above. The O.D. is the outside diameter of the glass barrel.

700 Series Syringes mm

		Outer Diameter Nominal		Inner Diameter Theoretical Bore
Model	Volume (µL)	mm	Inches	mm	Inches

75	5	6.604	0.260	0.343	0.014

701	10	6.604	0.260	0.485	0.019

702	25	7.747	0.305	0.729	0.029

705	50	7.747	0.305	1.030	0.041

710	100	7.747	0.305	1.457	0.061

725	250	7.747	0.305	2.304	0.091

750	500	7.747	0.305	3.256	0.135

Volumes are based on 60 mm scale length except models 75 and 701 which are based on 54.1 mm scale length. O.D. dimensions are nominal and typical, I.D. dimensions are theoretical.

1700 Series Syringes

		Outer Diameter Nominal		Inner Diameter Theoretical Bore
Model	Volume (µL)	mm	Inches	mm	Inches

1701	10	6.604	0.260	0.460	0.018

1702	25	7.747	0.305	0.729	0.029

1705	50	7.747	0.305	1.030	0.041

1710	100	7.747	0.305	1.457	0.057

1725	250	7.747	0.305	2.304	0.091

1750	500	7.747	0.305	3.256	0.128

1000 Series Syringes

		Outer Diameter Nominal		Inner Diameter Theoretical Bore
Model	Volume (mL)	mm	Inches	mm	Inches

1001	1.0	9.017	0.355	4.608	0.181

1001.25	1.25	8.566	0.329	5.151	0.203

1002 (thin wall)	2.5	9.525	0.375	7.285	0.287

1002 (thick wall)	2.5	10.338	0.407	7.285	0.287

1005	5.0	13.462	0.530	10.300	0.406

1010	10.0	17.653	0.695	14.567	0.574

1025	25.0	27.102	1.067	23.033	0.907

1050	50.0	36.881	1.452	32.573	1.282

1100	100.0	36.881	1.452	32.573	1.282

Volumes are based on 60 mm scale length except models 1100 which are based on 120 mm scale length. O.D. dimensions are nominal and typical, I.D. dimensions are theoretical.

Super Syringes

	Outer Diameter Nominal		Inner Diameter Theoretical Bore
Model	mm	Inches	mm	Inches

S0500	75	2.95	62	2.44

S1000	100	3.95	87	3.44

S1500	100	3.95	87	3.44

S2000	100	3.95	87	3.44

Hamilton Company USA
4970 Energy Way
Reno, Nevada 89502

Tel: (800) 648-5950
Fax: (775) 856-7259

E-mail: sales@hamiltoncompany.com
http://www.hamiltoncompany.com

Sales/Support
1 (888) 525-2123